Home
Pumps
DHW pumps
Circulating pump for the Wilo Top-Z hot water system (coupling, bronze)

Circulating pump for the Wilo Top-Z hot water system (coupling, bronze)

Short information

Max. flow rate: 7.0 - 10.0 m³/h Max. head: 5.0 - 9.0 m.a.c. Art. Threaded pipe connection: 1" - 1¼" Max. operating pressure: 10 bar Max. power consumption: 155 - 335 W Temperature range: 0...+80 °C

SKU: 2061964sbor

Add to Wishlist

Наименование	Краткая информация	Артикул	Price
DHW circulation pump Wilo Top-Z 30/7 DM	Max. flow: 7.00 m³/h Max. head: 5.00 m w.c. Art. Threaded pipe connection: 1¼" Max. power consumption: 155 W	2048341	₴21,766.80
DHW circulation pump Wilo Top-Z 30/7 EM	Max. flow: 7.00 m³/h Max. head: 5.00 m w.c. Art. Threaded pipe connection: 1¼" Max. power consumption: 185 W	2048340	₴22,872.60
DHW circulation pump Wilo Top-Z 25/10 DM	Max. flow: 10.00 m³/h Max. head: 9.00 m w.c. Art. Threaded pipe connection: 1" Max. power consumption: 310 W	2061965	₴36,607.80
DHW circulation pump Wilo Top-Z 25/10 EM	Max. flow: 10.00 m³/h Max. head: 9.00 m w.c. Art. Threaded pipe connection: 1" Max. power consumption: 335 W	2061964	₴38,703.00
DHW circulation pump Wilo Top-Z 30/10 DM	Max. flow: 10.00 m³/h Max. head: 9.00 m w.c. Art. Threaded pipe connection: 1¼" Max. power consumption: 310 W	2059858	₴40,565.40
DHW circulation pump Wilo Top-Z 30/10 EM	Max. flow: 10.00 m³/h Max. head: 9.00 m w.c. Art. Threaded pipe connection: 1¼" Max. power consumption: 335 W	2059857	₴42,893.40

Details

Details

Circulation pump for the Wilo Top-Z hot water system (coupling, bronze)

Wilo TOP-Z circulation pumps circulate water in heating, hot water and floor heating systems. Wilo TOP-Z circulation pumps are quite compact and lightweight, installed directly on the pipeline and operate almost silently. Suitable for systems of almost all private houses, not easy to install and have a long service life. The installation of the Wilo TOP-Z electronic high-efficiency pump saves up to 90% of energy compared to an unregulated circulation pump. If, however, the Wilo TOP-Z pump is used in the hot water supply system, then the energy savings compared to standard circulation pumps will be 80%.

Equipment and functions of Wilo TOP-Z circulation pumps:

manual power adjustment with 3 speed settings
Wilo pumps TOP - Z EM with single-phase motor:

P ₂ up to 90 W: Integrated winding protection against overheating
P ₂ = 180 W: Complete motor protection by winding safety contact in combination with tripping device

Wilo pumps TOP - Z DM with 3-phase motor:

P ₂ up to 90 W: Integrated winding protection against overheating
P ₂ ≥ 180 W: Complete motor protection with integrated electronic tripping system

fault indicator
contact for generalized fault signaling
control indicator for direction of rotation
connection to a 3-phase 230 V mains supply with optional switching plug
Wilo pump housing TOP - Z bronze or gray cast iron (may be stainless steel depending on the type)
combined flange PN 6/PN 10 (for DN 40 – DN 65)
thermal insulation for use in heating systems
Additional functions when retrofitting with protection module C:

fault signaling SSM as potential-free NC contact;
operation signaling SBM as potential-free normally open contact
control input "Off" by priority" with an external potential-free contact (NC contact)
blockage detection
complete motor protection for the Wilo pump TOP - Z built-in disconnect device

Wilo double pump control system (two pumps installed in parallel): Master/standby operating mode (automatic pump changeover on fault/timer)

Equipment and material of Wilo TOP-Z circulation pumps:

cable entry possible on both sides (only for single-phase and three-phase pumps with P ₂ ≥180 W)
serial thermal insulation
Wilo pump housing TOP - Z : stainless steel/bronze/grey cast iron (depending on type)
impeller: synthetic material
shaft: stainless steel/ceramic (depending on type)
bearings: graphite impregnated with synthetic resin